How we typically close an inground pool around here, and what has to happen before the hard freeze.
Written by the crew at Legacy Backyards in Lincoln. [NEEDS INFO: author name and credentials, or who on the team should be named as the reviewer.]
Close the pool before overnight freezes start sticking around. We don't pick one date and close every pool that week. We watch the forecast. Clean the pool, get the water in range, and winterize the equipment so water isn't sitting in the pump, filter, heater, or lines. Set the water level for your cover, then put the cover on. If you have an automatic safety cover, plan on leaving a cover pump on it all winter, and don't drop the water farther than the manufacturer allows. Always check your equipment and cover manuals.
For after closing day, see winter care and the cover pump. For spring, see opening.


We don't close on a calendar date
A warm October followed by a late heat wave just means a longer stretch under the cover. Waiting until the first hard freeze is already here means you're fighting ice on the pad. The useful rule is to close before those overnight freezes become routine, while you can still work with liquid water in the lines.
[NEEDS INFO: the closing window we actually tell customers, and whether Legacy or P&W does professional closings. A short, approved note about how we typically call that week (no addresses) would help.]
Clean it and get the water in range first
A dirty close makes a harder open. Brush, vacuum, skim. Empty the baskets. Test the water and get pH, alkalinity, and sanitizer in a normal range before you shut the system down. Follow the labels. If you add a winterizing chemical, use it as directed after the water is already in decent shape. It doesn't replace cleaning.

Winterize the pad so water isn't sitting in it
That's the whole point of this step. Frozen water in a pump or a heater is a spring problem you don't want.
Typical closing work, always subject to your pump, filter, heater, salt cell, and automation manuals:
- Run the system long enough to circulate any closing chemicals, then shut it down in the order the manufacturer specifies.
- Drain the pump, filter, heater, chlorinator or salt cell, and anything else that can hold water.
- Open the drain plugs and store them with the baskets, gizmos, and fittings in one labeled bag or bucket.
- Blow out or otherwise clear the lines the way your installer told you, and put winter plugs where they belong.
- Don't leave water sitting in the low spots of the piping.
An automation schedule will not winterize the pad for you. If you're not sure how your pad was meant to be closed, have someone who knows that equipment do it. Guessing is how fittings crack.
Set the water level for your cover
This is one of the easier ways to damage a cover or a pool.
Automatic safety covers. Several manufacturers, including Coverstar in its winter use guide, say the water should not be lowered more than a small amount below normal when the cover will stay closed. Coverstar's number is no more than 5 inches below normal, and they want that level held whenever the cover is closed. The water under the cover helps support snow and ice. Check your own manual for the number that applies to your system. Don't assume Coverstar's figure is universal.
Mesh or solid safety covers. These usually go on tight over anchors. The water level is often lowered according to that cover and the pool type. Fiberglass, vinyl, and concrete can have different guidance. Follow what came with the cover and what your installer told you.
If you're unsure, ask before you start draining.
Get the cover on right
Around here the cover is a safety barrier and your first defense against a long winter of leaves, snow, and thaw.
For an automatic cover, close it only when the fabric is clear, then put the cover pump on it and run the discharge hose somewhere the water can go without making a rink on the walk. See the cover pump article.
For a mesh or solid safety cover, use the springs and anchors the way they were designed. Don't leave big gaps. A solid cover will need a way to get rain and snowmelt off it.
Don't walk on a cover unless the manufacturer says you can. And a cover doesn't replace a fence, or you keeping an eye on the yard.
After we leave
Plan to look at the cover, the pump, the water level, and the fence through the winter. Midwinter thaws around here can put a surprising amount of water on a cover. That's what the winter care piece is for.
Doing it yourself, or having us do it
If you already know your equipment, you can close a pool carefully. If this is your first winter, the pad is complicated, or you've never winterized that automatic cover, a professional closing is usually the safer day.
[NEEDS INFO: confirm whether Legacy, P&W, or both currently offer closings, and the wording you want.]
If you're still choosing a cover for a new pool, talk about winter now. Don't wait until October and hope the cover you picked can handle it. We can go through that in a consultation.
FAQs
When should I close my pool in Central Illinois?
Before consistent freezing weather. The exact week changes with the year. [NEEDS INFO: any typical window you want published.]
Do I drain the pool all the way?
No. You set the water to the level your cover and pool type require. Draining an inground pool the wrong way can cause real trouble.
Can I use my automatic cover as the winter cover?
Some owners do. Coverstar, for one, stays neutral on that choice, lists extra care steps, and notes that winter use is generally not covered by the cover warranty. Read your own manual and our pump article.
What if I have a vinyl liner?
Follow the liner-specific water-level and closing guidance from your installer and the liner manufacturer. Pay attention to leaving water in the pool and to ice at the fittings.

